Have you been in search of help around Installing A Bathtub?
Mounting a tub isn't precisely brain surgery, however it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old tub with a new one is likewise a moderately hard project. If the old bathtub is easily available, the task can relocate immediately; if you need to open up a wall to get rid of the old tub and position the new bathtub, the task is much harder. In either instance, the project is within a home handyman's abilities, although you will require an assistant to leave the old tub and also embeded in the new one. See to it you have qualified yourself for the task and also are comfortable attempting it. Rather than employing a professional to take over a halfway-completed task, it is far better to take into consideration employing one before you start. Opportunities are you might need a specialist plumber to make tube connections.
This article will assist you install a new tub in your restroom if you have actually currently acquired a new tub and do not need to alter the plan of your previous supply of water pipes.
Your tools and also product checklist should make up the following:
Preparing for the Setup
To start with, the supporting structure provided with the bathroom ought to be fitted (if needed) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps device to stop stress on the bathtub.
Fit the adaptable faucet ports to the bottom of both faucets using 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. See to it you make use of all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must currently prepare to be suited its last placement.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installation, then the first thing you ought to do is disconnect the water supply. After doing so, switch on the faucets to drain any water continuing to be in the system. The process of eliminating the existing faucets can be fairly troublesome because of the limited access that is often the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipelines have actually been eliminated, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from transforming throughout this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Using both wood boards under its feet, put the bathtub in the required setting. The wooden boards are useful in evenly spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto four little points.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the level and readjusting the feet on the tub up until the spirit level checks out degree.
To mount faucets, fit all-time low of the furthest adaptable faucet port to the appropriate supply pipe by making a compression join; then do the same for the other tap.
Switch on the supply of water and inspect all joints and also brand-new pipework for leaks and tighten them if essential. Fill the tub as well as likewise examine the overflow electrical outlet as well as the typical outlet for leaks.
Finally, deal with the bathroom paneling as defined in the producer's instruction manual. Tiling and also securing around the bath tub ought to wait up until the tub has actually been utilized a minimum of once as this will certainly settle it right into its last position.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a link to the existing supply pipes.
If you need to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in place in between the faucet and the sink. Secure the faucet in position with the manufacturer supplied backnut. As soon as the tap is securely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal faucet connectors. The previous type should be attached to the tap ends initially, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to break a rigid seal, causing the water to pass through the wall between the bathroom and the tiling, bring about complications with dampness and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your components as well as fittings. They are sold in tubes and also cartridges, and are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill up the bath tub with water prior to securing, to enable the activity experienced when the tub is in use. The sealer can break rather very early if you do not take into consideration this movement prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently available on the market. It is a good idea to fit the ceramic tiles using waterproof or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that entry on Tools You Need to Install a New Bathtub while surfing around the internet. Enjoyed our review? Please share it. Let another person locate it. I am grateful for your time. Visit again soon.
Immediate help? Contact.